Certification QPL pour les gammes PM907S et PM98S

Exxelia annonce l’obtention de la qualification ESA/QPL pour ses gammes de condensateurs film : PM907S et PM948S.


 

Les gammes PM907S et PM948S de condensateurs film viennent d’être officiellement qualifiées QPL par l’organisme européen ESCC (European Space Components Coordination). La certification QPL atteste que les performances du produit ont été validées par un organisme accrédité indépendant. Les produits qualifiés QPL offrent une qualité et fiabilité supérieures, qui répondent aux exigences des applications spatiales.

Les gammes PM907S et PM948S appartiennent à la famille des condensateurs film polyester métallisés (PET), haute précision. La gamme PM907S est adaptée aux tensions de 50V à 1250V, et offre une capacité allant de 82nF jusqu’à 180μF. La gamme PM948S couvre quant à elle les tensions situées entre 50V et 630V, et offre une capacité allant de 22nF jusqu’à 47μF.

Ces deux gammes supportent des conditions extrêmes, des températures oscillant entre -55°C et +125°C, tout en offrant une forte concentration d’énergie, de faibles ESR et ESL, ainsi qu’un courant RMS élevé.
Ces produits sont principalement utilisés dans des alimentations à découpage et pour la fonction de filtrage des BUS.

La liste des gammes de condensateurs film certifiées QPL et développées par Exxelia, comprend désormais les gammes :
– PM90S
– PM907S
– PM96S (T)
– PM94S
– PM948S
– MKT5
– KM111S
– KM94S
– HT78PS

Published on 06 Jul 2016 by Marion Van de Graaf

Elevating AED performance with Exxelia Ohmcraft resistors & Alcon Power film capacitors

That's why we're proud to introduce our cutting-edge components, Exxelia Ohmcraft Resistors and Exxelia Alcon Power film capacitors, engineered specifically to elevate the performance and reliability of AED devices.   Exxelia Ohmcraft Resistors: Precision Resistors for the World’s Most Advanced Medical Applications. Designed with precision and reliability at the core, Exxelia Ohmcraft Resistors are the standard in high-performance applications. Their stability, low noise, and high pulse load capability ensure optimal functionality in AEDs, contributing to their life-saving accuracy. For example, Exxelia Ohmcraft’s high voltage resistors have played a critical role in AED operation for more than 20 years, especially : HVC series, SM series, HVR series, HVD series, and Custom. - Voltage Ratings to 40 kV (HVD series) - Resistance Values to 4 TΩ (HVR series) - Ultra High Stability - Very Low Noise - Ratio Tolerances to 0.1% for all series - TCR to 25 ppm/°C - TCR Tracking to 5 ppm/°C - VCR to 1 ppm/V (SM series) - Custom Configurations   “In an emergency medical situation, reliability is critical—automated external defibrillators must always work and never fail. At Exxelia Ohmcraft, all of our resistors go through rigorous testing to ensure complete reliability. In addition, to maintain their portability, AEDs are manufactured to be as small as possible. Our proprietary Micropen technology enables us to print surface mount resistors that are high in capability, and small in size, making them perfect for applications of this kind.” said Vice President Exxelia Ohmcraft.     Exxelia Alcon Power film capacitors: Powering the Future of AEDs Harnessing advanced technology, Exxelia Alcon Capacitors are the pinnacle of power film capacitors. With a focus on energy efficiency and enhanced reliability, these capacitors empower AEDs to deliver rapid and consistent energy discharges, crucial in critical moments, especially the Exxelia Alcon DFC energy discharge     - High charge / discharge cycles 2 000 to 10 000 - Very low ESR - Very low dissipation factor - Silicon insulated wire termination and faston terminations - Plastic and Aluminum enclosures round and oval - Monophasic and Biphasic designs - Flame retardancy UL94-V0   Key Benefits of Exxelia components for AEDs: + Reliability: Engineered for consistent performance under extreme conditions, ensuring AEDs are always ready for action. + Precision: High-precision components that guarantee accurate energy delivery for efficient defibrillation. + Durability: Withstand shock and vibration, ensuring longevity and reliability in every use case. + Safety: Compliance with stringent quality standards, assuring the highest level of safety in life-saving situations.   Why Choose Exxelia for your AED Components? Our commitment to quality, backed by rigorous testing and adherence to industry standards (RoHS, Sn-Pb, UL94-V0) ensures that AEDs equipped with Exxelia Ohmcraft high voltage resistors and Exxelia Alcon Power film capacitors perform flawlessly when it matters most. Partner With Us Elevate your AEDs to the next level of performance and reliability with Exxelia Ohmcraft and Exxelia Alcon. Contact our team of experts today to discover how our components can enhance the life-saving capabilities of your devices.   Contact us    

What you should know about electrolytic aluminum capacitors ?

1. Basic construction Structure of an electrolytic aluminum capacitor is shown hereunder: Anode: aluminum foil Dielectric: aluminum oxide Papers spacers impregnated with electrolyte Ionic conduction assumed by electrolyte Cathode: aluminum foil   The positive plate is an etched aluminum foil covered with alumina which is the dielectric of the capacitor. The negative plate is constituted by a second aluminum foil which serves as a current supply, and by electrolyte-impregnated papers layers. The metal used for anode is a ≥ 99,98 % grade aluminum. The dielectric has a thickness of 13 Å / V. The aluminum used for the cathode is a ≥ 98 % grade aluminum covered with a dielectric layer with a thickness of about 40 Å.   > See our capacitors in catalog 2. Diagram of the equivalent circuit CA = Capacitance of the anode CK = Capacitance of the cathode Rp = Parallel resistance due to the aluminum oxide f Ilms. RL = Series resistance of connections, plates and impregnated spacer. Ls = Inductance of winding and connections.   A standard simplified diagram is :   Cs is the series capacitance of both anode and cathode capacitances. Electrolytic aluminum capacitors are naturally polarized because of the insulating f Ilm on the anode. Given the very thin aluminum oxide layer, a reversed voltage should not exceed 1.5 V when there is energy supply. Short duration reverse voltages can be absorbed by special construction, second anode replacing the former cathode. 3. Electrical characteristics ✪ Rated capacitance Cr The rated capacitance is defined at 100 Hz and at ambient temperature.   ✪ Rated voltage Ur Ur is the maximum DC voltage which may be applied in continuous operation. When applying a superimposed alternating voltage, the peak value of the resulting waveform should not exceed the rated voltage.   ✪ Peak voltage Up Up is the maximum repetitive voltage which can be applied within short periods. Defined in CECC 30 300 and IEC 60 384-4:  1000 cycles of 30 s charge followed by a no load period of 5 min. 30 s with upper category temperature. Up ≤ 1,15 UR (UR ≤ 315 V) Up ≤ 1,10 UR (UR > 315 V)   ✪ Dissipation factor Tan The dissipation or loss factor is defined by its tangent Tand   ✪ Equivalent series resistance ESR The relation between ESR and dissipation factor Tand.   ✪ Impedance Z - Inductance L The impedance is given by:  Z =g R2 + (Lv –1 )2                         Cv L inductance. Generally L = 5 to 20 nH   Z and ESR as function of frequency typically follows the chart:    ✪ Permissible ripple current (I r.m.s.) The current is defined at the maximum climatic category and at 100 Hz. It is the root mean square value r.m.s. The value I0 is the rated value for calculations of expected life up to3 I0.   ✪ Leakage current Il Il is measured at 20°C after a 5 min. polarization under rated voltage. For CR in μF and UR in V:   Il ≤ 0,01 CR UR or 1 μA* when CR UR ≤ 1000 μC  Il ≤ 0,006 CR UR + 4 μA when CR UR > 1000 μC For UR > 350 VDC it can be specified:  with K = 4, 6 or 8 or  Il ≤ 0,3 (CR UR)0,7 + 4 μA (CECC 30 300) * Whichever is the greater   ✪ Characteristics Versus temperature (typical values).   - Capacitance drift Versus temperature - ESR and Z drifts at 100 Hz Versus temperature - Leakage current drift Versus temperature > See our capacitors in catalog 4. Specification to apply Electrolytic aluminum capacitors are defined in:  NF and UTE French national standard CECC European specifications IEC international specifications Quality insurance procedures are described in these specifications. 5. Endurance tests / life time ✪ Standard endurance test at max category temperature:  Standard endurance tests do not exceed 2000 hours at 125°C. However, present EXXELIA technologies concerning liquid electrolytes have led to endurance tests up to 5000 hours at 125°C (PRORELSIC 125 - FELSIC 125 RS) and even 20000 hours at 125°C (PRORELSIC 145 - ALSIC 145).   ✪ Performance requirements on standard endurance tests Permissible capacitance drift ∆C/C (%) Permissible increase factors on Tand, ESR, Z and Il initial values   (1) Tand or ESR: for initial value, take standard value. (2) Z: for initial value, take specified value (see data sheet ). Specific requirements can be taken into consideration with regards to initial values of dissipation factor or equivalent series resistance and impedance.   ✪ Failure criteria for electrolytic capacitors Failure criteria are defined in CECC 30 301 Non measurable defaults leading to complete failure. Measurable defaults leading to adjustment losses of the load circuit (failure due to variations).   - Non measurable defaults They might be summed up as:  Open circuit Short circuit Operation of pressure relief device Severely damaged insulation Unusable terminations   - Measurable defaults Variations exceeding the values given below characterize a default. Capacitance drift ∆C/C (%): 3 times the limit for standard endurance testing or 50 % (whichever is the smallest). Tand or ESR: 3 times standard max initial values. Z: 3 times standard max initial values. Il: initial limit (under load conditions). Specific requirements can be taken into consideration with regards to lower drifts.   Influence of main parameter on operational life. - Temperature The capacitors operational life is highly dependent upon its internal temperature Ui and therefore upon the ambient temperature and the ripple current. Knowing ESR and dissipated power values one can figure out, the internal temperature rise and then determine the capacitors expected life. With present high boiling point electrolytes Ui max = 125 to 185°C depending on styles. - Ripple current The ripple current flowing through the capacitor increase the internal temperature through power dissipation. Standards define the permissible current at 100 Hz and generally consider a temperature rise of 5 to 10°C of max category temperature. Current waveforms and frequencies make it difficult to clearly determine the capacitors internal temperature rise, which defines the operationally life. Experiments confirm following relationship:  Ui = Ua + (Uc - Ua) K Where:  Ui = Internal hot spot temperature Ua = Ambient temperature Uc = Case temperature K = Parameter depending upon case diameter and cooling Ø ≥ 51 k = 2 ± 0,5 Ø < 51 k = 1,5 ± 0,5    (air cooling - 0,2 m/s)   r.m.s. value according to current waveform.   - Dissipated power versus case dimension For calculations of ripple currents, considering an internal temperature rise of 10°C   P = ESR.I ² P = Dissipated power (mW) (Ui - Ua = 10°C) ESR: Equivalent series resistance (100 Hz 20°C) I: Ripple current (r.m.s. value at 100 Hz) For different frequencies from 100 Hz, I must be multiplied by the factor F, according to above chart.   - Thermal resistance Rth and air cooling Rth is static thermal resistance (without cooling) between capacitor central hot spot and ambient temperature measured at a distance of one capacitor diameter   Forced or not cooling air can lead to a significant decrease of these values. Consequently, r.m.s. ripple current can be increased as a function of air cooling speed:  This parameter shall be applied to one capacitor alone. For capacitors in bank, ambient temperature must be strictly equal around all capacitors. - Quality guaranty We guarantee products manufactured during 2 years from the data of shipment against defaults of material and assembly. This guaranty can be involved by the buyer only if our products are used within normal conditions, always according to the state of the art and taking in account storage conditions. The equipment design should take into consideration possible failures of our capacitors and related effects in order to avoid them. Guaranty is not applicable for damages occurred by surge voltage, irregular use, polarity inversion or maintenance default. Guaranty is exclusively limited to the replacement of individual defective capacitors within the terms of delivery. This rule applied to all cases and particularly to any further consequence of failures. - Reliability Failure rate:  FR = Number of components tested x test duration / Number of failures Failure rate is measured in FIT (failure in time = 10–9 / hour). The failure rate is set up during the life time of the capacitor (phase II) I. Early failure phase (generally excluded during ageing process). II. Operational life time of the capacitors III. End of life   Mean time between failures MTBF = 1/FR mesured in years Multiplying factor of FR with voltage and temperature   > See our capacitors in catalog 6. Information on application ✪ Cleaning solvents Use aliphatic alcohols, such as denatured ethyl alcohol, isopropanol, or butylacetate, or else alkaline d Iluted solutions. Avoid incompatible solvents (halogenous for example).   ✪ Shelf life There is no electrical characteristics variation for long periods of storage except leakage current which can increase. It is caused by chemical reactions between the dielectric alumina and the electrolyte. These reactions are reversible when switched on. Capacitors can generally be stored at temperature between –5° and +50°C without reforming for the following periods of time:  For UR ≤ 100 V, storage time:     5 years (up to 10 years under specific conditions) For 100 V < UR ≤ 360 V storage time:     3 years For 360 V < UR < 500 V storage time:     1 year For UR ≤ 500 V, storage time:     6 months Generally when these periods are overstepped, one hour at rated voltage causes the decrease of leakage current under the specified limits. An other way to avoid this leakage current increase problem is to always limit ava Ilable power through capacitor during first seconds or minutes after storage or transport, according to the following chart:    ✪ Low pressure resistance EXXELIA capacitors can be used with ambient low pressure decreasing up to 10 mbar (altitude 28000 m – 92000 feet).   ✪ Mounting screw terminals capacitors (FELSIC) Capacitors may be used vertically (terminals on top) or horizontally. When used horizontally, the following position in relation to the safety vent, is recommended:  Mounting capacitors in series may be used for operating voltage exceeding Ur. See FELSIC in bank.   ✪ Mounting solder type capacitors They may be used in any position. During mounting, avoid applying excessive force to capacitor pins or wires. There is a risk of damaging internal connections. After soldering and for the same reasons, do not try to move the capacitor&#39;s body. ✪ Electrolytes: safety rules Electrolytes used in EXXELIA capacitors are manufactured by EXXELIA. Main solvents are generally g butyrolactone and ethylene glycol, very stable high boiling point solvents. Ionic conductive salts in electrolyte induce a very weak acidity (pH 5 to 7).   ✪ Environment In aluminium capacitors with liquid electrolyte there is no component showing a pollution risk, in small amounts, of air or water. EXXELIA is always involved in this security field particularly in using chemicals for electrolyte, without well-known risks. Dimethylformamide (DMF) dangerous solvent forbidden in several uses is completely excluded by EXXELIA,since 1990. There is no halogen compound such as chlorofluorocarbon (CFC or FCKW in german) or polychlorobiphenyl (PCBPyralene) or pentabromodiphenylether or octabromodiphenylether. There is neither benzene, toluene or phenyl compound nor explosive such as picric acid, nor asbestos in plastic covers. All the capacitors made by EXXELIA since 1991, can be scrapped or used in raw materials recycling processes without special care in compliance with Community rules. EXXELIA aluminium capacitors with non-solid electrolyte are particularly suitable for different kinds of environment taking in account severity increasing laws. European directives 2003/11/EC, 2002/96/EC (WEEE) and 2002/95/EC (RoHS) applies to all EXXELIA capacitors including every solder type, manufactured with pure tin coated pins or wires, since at least January 2006.   > See our capacitors in catalog